# Fire and light: flame spray pyrolysis and laser ablation in liquids

> Two physical routes to nanoparticles side by side. Flame spray pyrolysis burns a precursor spray: the flame core at 2500–3500 °C vaporises it and nucleates particles that sinter, agglomerate and are collected as dry oxide powder, continuously, at up to 50–100 g h⁻¹ in a pilot reactor. Laser ablation in liquid fires short pulses at a metal target under water: a plasma, then a cavitation bubble that confines the particles for under a millisecond, gives a ligand-free colloid, now at up to 4 g h⁻¹ with a 500 W picosecond laser.

- Page: https://www.labcanvas.com/templates/graphical-abstracts/fire-light-flame-spray-pyrolysis-laser-ablation-liquids
- Open in the LabCanvas editor (LabCanvas account): https://www.labcanvas.com/editor.html?template=flame-spray-pyrolysis-and-laser-ablation-in-liquids
- Updated: 2026-10-14
- Category: Graphical abstracts
- Method: Graphical abstract
- Starting materials: FSP: metal 2-ethylhexanoates, nitrates, acetylacetonates or alkoxides in xylene, toluene or ethanol; LAL: a solid metal target under water or a solvent
- Product: FSP: dry, loosely agglomerated oxide (or metal) nanopowders; LAL: ligand-free metal colloids
- Key result: Flame core 2500–3500 °C; 50–100 g h⁻¹ pilot FSP (Dimitriou et al. 2023); bubble < 1 ms (Ibrahimkutty et al. 2015); up to 4 g h⁻¹ LAL (Streubel et al. 2016)
- Figure: 1920 × 1080 px, 79 editable layers (2 generated objects with settings)

## Steps

1. **Spray and burn**: The precursor solution is atomised at a nozzle and lit by a pilot flame; the core near the tip reaches 3500–2500 °C, vaporising the precursor and nucleating particles (Dimitriou et al. 2023)
2. **Sinter, agglomerate, collect**: Coagulation and sintering at 1700–600 °C, agglomerates below 600 °C and aggregates at 400–200 °C; collected as dry powder; 50–100 g h⁻¹ MgAl₂O₄ in a pilot reactor (Dimitriou et al. 2023)
3. **Ablate under liquid**: A laser pulse on a metal target under liquid makes a plasma, then a cavitation bubble that confines the particles for under a millisecond (Ibrahimkutty et al. 2015)
4. **Ligand-free colloid**: The particles leave with clean, charged surfaces that bind biomolecules and supports (Zhang, Gökce & Barcikowski 2017)
5. **Scale**: PLAL usually makes milligrams per hour (Khairani et al. 2023); a 500 W, 10 MHz picosecond laser with a 500 m s⁻¹ scanner reached 4 g h⁻¹ (Streubel et al. 2016)

## Uses

- Graphical abstracts on gas-phase and physical nanoparticle synthesis
- Talks comparing flame aerosol and laser-ablation routes
- Teaching particle formation in flames and cavitation bubbles

## References

1. Dimitriou, Psathas, Solakidou & Deligiannakis, “Advanced flame spray pyrolysis (FSP) technologies for engineering multifunctional nanostructures and nanodevices”, Nanomaterials 2023. https://doi.org/10.3390/nano13233006 (review)
2. Teoh, Amal & Mädler, “Flame spray pyrolysis: an enabling technology for nanoparticles design and fabrication”, Nanoscale 2010. https://doi.org/10.1039/c0nr00017e (review)
3. Mädler, Kammler, Mueller & Pratsinis, “Controlled synthesis of nanostructured particles by flame spray pyrolysis”, J. Aerosol Sci. 2002. https://doi.org/10.1016/S0021-8502(01)00159-8 (method origin)
4. Pratsinis, “Flame aerosol synthesis of ceramic powders”, Prog. Energy Combust. Sci. 1998. https://doi.org/10.1016/S0360-1285(97)00028-2 (further reading)
5. Zhang, Gökce & Barcikowski, “Laser synthesis and processing of colloids: fundamentals and applications”, Chem. Rev. 2017. https://doi.org/10.1021/acs.chemrev.6b00468 (review)
6. Ibrahimkutty et al., “A hierarchical view on material formation during pulsed-laser synthesis of nanoparticles in liquid”, Sci. Rep. 2015. https://doi.org/10.1038/srep16313 (primary)
7. Khairani, Mínguez-Vega, Doñate-Buendía & Gökce, “Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for high-throughput production”, Phys. Chem. Chem. Phys. 2023. https://doi.org/10.1039/d3cp01214j (review)
8. Streubel, Barcikowski & Gökce, “Continuous multigram nanoparticle synthesis by high-power, high-repetition-rate ultrafast laser ablation in liquids”, Opt. Lett. 2016. https://doi.org/10.1364/OL.41.001486 (primary)
9. Neddersen, Chumanov & Cotton, “Laser ablation of metals: a new method for preparing SERS active colloids”, Appl. Spectrosc. 1993. https://doi.org/10.1366/0003702934066460 (method origin)

Credit: Drawn by LabCanvas after Dimitriou et al., Nanomaterials 2023 (doi:10.3390/nano13233006); Teoh, Amal & Mädler, Nanoscale 2010 (doi:10.1039/c0nr00017e); Mädler et al., J. Aerosol Sci. 2002 (doi:10.1016/S0021-8502(01)00159-8); Zhang, Gökce & Barcikowski, Chem. Rev. 2017 (doi:10.1021/acs.chemrev.6b00468); Ibrahimkutty et al., Sci. Rep. 2015 (doi:10.1038/srep16313); Khairani et al., Phys. Chem. Chem. Phys. 2023 (doi:10.1039/d3cp01214j); Streubel et al., Opt. Lett. 2016 (doi:10.1364/OL.41.001486). Ladders not to scale.

## Questions

**What does the “Fire and light: flame spray pyrolysis and laser ablation in liquids” template show?** Two physical routes to nanoparticles side by side. Flame spray pyrolysis burns a precursor spray: the flame core at 2500–3500 °C vaporises it and nucleates particles that sinter, agglomerate and are collected as dry oxide powder, continuously, at up to 50–100 g h⁻¹ in a pilot reactor. Laser ablation in liquid fires short pulses at a metal target under water: a plasma, then a cavitation bubble that confines the particles for under a millisecond, gives a ligand-free colloid, now at up to 4 g h⁻¹ with a 500 W picosecond laser.

**What are the steps shown in “Fire and light: flame spray pyrolysis and laser ablation in liquids”?** 1. Spray and burn: The precursor solution is atomised at a nozzle and lit by a pilot flame; the core near the tip reaches 3500–2500 °C, vaporising the precursor and nucleating particles (Dimitriou et al. 2023). 2. Sinter, agglomerate, collect: Coagulation and sintering at 1700–600 °C, agglomerates below 600 °C and aggregates at 400–200 °C; collected as dry powder; 50–100 g h⁻¹ MgAl₂O₄ in a pilot reactor (Dimitriou et al. 2023). 3. Ablate under liquid: A laser pulse on a metal target under liquid makes a plasma, then a cavitation bubble that confines the particles for under a millisecond (Ibrahimkutty et al. 2015). 4. Ligand-free colloid: The particles leave with clean, charged surfaces that bind biomolecules and supports (Zhang, Gökce & Barcikowski 2017). 5. Scale: PLAL usually makes milligrams per hour (Khairani et al. 2023); a 500 W, 10 MHz picosecond laser with a 500 m s⁻¹ scanner reached 4 g h⁻¹ (Streubel et al. 2016).

**What are the starting materials and the product?** Starting materials: FSP: metal 2-ethylhexanoates, nitrates, acetylacetonates or alkoxides in xylene, toluene or ethanol; LAL: a solid metal target under water or a solvent. Product: FSP: dry, loosely agglomerated oxide (or metal) nanopowders; LAL: ligand-free metal colloids.

**Which papers is “Fire and light: flame spray pyrolysis and laser ablation in liquids” based on?** Dimitriou, Psathas, Solakidou & Deligiannakis, “Advanced flame spray pyrolysis (FSP) technologies for engineering multifunctional nanostructures and nanodevices”, Nanomaterials 2023 (doi:10.3390/nano13233006); Teoh, Amal & Mädler, “Flame spray pyrolysis: an enabling technology for nanoparticles design and fabrication”, Nanoscale 2010 (doi:10.1039/c0nr00017e); Mädler, Kammler, Mueller & Pratsinis, “Controlled synthesis of nanostructured particles by flame spray pyrolysis”, J. Aerosol Sci. 2002 (doi:10.1016/S0021-8502(01)00159-8); Pratsinis, “Flame aerosol synthesis of ceramic powders”, Prog. Energy Combust. Sci. 1998 (doi:10.1016/S0360-1285(97)00028-2); Zhang, Gökce & Barcikowski, “Laser synthesis and processing of colloids: fundamentals and applications”, Chem. Rev. 2017 (doi:10.1021/acs.chemrev.6b00468); Ibrahimkutty et al., “A hierarchical view on material formation during pulsed-laser synthesis of nanoparticles in liquid”, Sci. Rep. 2015 (doi:10.1038/srep16313); Khairani, Mínguez-Vega, Doñate-Buendía & Gökce, “Green nanoparticle synthesis at scale: a perspective on overcoming the limits of pulsed laser ablation in liquids for high-throughput production”, Phys. Chem. Chem. Phys. 2023 (doi:10.1039/d3cp01214j); Streubel, Barcikowski & Gökce, “Continuous multigram nanoparticle synthesis by high-power, high-repetition-rate ultrafast laser ablation in liquids”, Opt. Lett. 2016 (doi:10.1364/OL.41.001486); Neddersen, Chumanov & Cotton, “Laser ablation of metals: a new method for preparing SERS active colloids”, Appl. Spectrosc. 1993 (doi:10.1366/0003702934066460).

**Can I edit the “Fire and light: flame spray pyrolysis and laser ablation in liquids” template?** Yes. Open it in the LabCanvas editor: all 79 layers are editable, including 2 generated objects (structures, plots, equipment) with their own settings. Change the text, colours and layout, then export PNG, TIFF or PDF at the width and DPI the journal asks for.

**Do I need an account to use this template?** Not to view it here. To open and edit it, sign in to LabCanvas or create a free account (the free plan keeps up to 3 designs). Downloading the figure is part of LabCanvas Pro (US$19 a month or US$199 a year).
