# PEM fuel cells: membrane, ionomer and catalyst layer, from molecule to stack

> A zoom-out through a proton-exchange membrane fuel cell. The PFSA ionomer (Nafion) is a Teflon-like backbone with side chains ending in sulfonic acid; hydrated, it forms parallel water channels 1.8–3.5 nm wide through which protons move. The same ionomer coats platinum on carbon in the catalyst layer, where protons, electrons and oxygen must meet; cutting platinum to about 0.1 mg cm⁻² exposes an oxygen-transport resistance near the Pt. The cell and stack carry the power-density goals of 6 kW L⁻¹ by 2030 and 9 kW L⁻¹ by 2040.

- Page: https://www.labcanvas.com/templates/graphical-abstracts/pem-fuel-cells-membrane-ionomer-catalyst-layer-molecule-stack
- Open in the LabCanvas editor (LabCanvas account): https://www.labcanvas.com/editor.html?template=pem-fuel-cell-membrane-ionomer-catalyst-layer
- Updated: 2026-10-14
- Category: Graphical abstracts
- Method: Graphical abstract
- Starting materials: A PFSA ionomer, platinum on carbon, a gas-diffusion layer; hydrogen and air
- Product: Electricity and water from a membrane electrode assembly in a stack
- Key result: Channels 1.8–3.5 nm, mean 2.4 nm, crystallites ~(5 nm)², ~10 vol% (Schmidt-Rohr & Chen 2008); Pt 0.4–0.8 → ~0.1 mg cm⁻², losses above 1 A cm⁻² (Kongkanand & Mathias 2016); 6 and 9 kW L⁻¹ goals (Jiao et al. 2021)
- Figure: 1920 × 1080 px, 87 editable layers (3 generated objects with settings)

## Steps

1. **The ionomer**: A PTFE backbone with perfluoroether side chains ending in –SO₃H, which gives up its proton in water (Kusoglu & Weber 2017)
2. **The membrane**: Hydrated, it forms parallel water channels 1.8–3.5 nm across (mean 2.4 nm at 20 vol% water), held by crystallites of about (5 nm)² (Schmidt-Rohr & Chen 2008)
3. **The catalyst layer**: The ionomer is also the binder and proton path around Pt on carbon (Holdcroft 2014); at ~0.1 mg Pt cm⁻² oxygen reaching the Pt limits currents above 1 A cm⁻² (Kongkanand & Mathias 2016)
4. **The stack**: Power-density goals of 6 kW L⁻¹ by 2030 and 9 kW L⁻¹ by 2040 (Jiao et al. 2021)

## Uses

- Graphical abstracts on fuel cells and ionomers
- Teaching how a PEM fuel cell membrane conducts protons
- Talks on low-platinum catalyst layers

## References

1. Schmidt-Rohr & Chen, “Parallel cylindrical water nanochannels in Nafion fuel-cell membranes”, Nat. Mater. 2008. https://doi.org/10.1038/nmat2074 (primary)
2. Kusoglu & Weber, “New insights into perfluorinated sulfonic-acid ionomers”, Chem. Rev. 2017. https://doi.org/10.1021/acs.chemrev.6b00159 (review)
3. Holdcroft, “Fuel cell catalyst layers: a polymer science perspective”, Chem. Mater. 2014. https://doi.org/10.1021/cm401445h (review)
4. Kongkanand & Mathias, “The priority and challenge of high-power performance of low-platinum proton-exchange membrane fuel cells”, J. Phys. Chem. Lett. 2016. https://doi.org/10.1021/acs.jpclett.6b00216 (review)
5. Jiao et al., “Designing the next generation of proton-exchange membrane fuel cells”, Nature 2021. https://doi.org/10.1038/s41586-021-03482-7 (review)
6. Debe, “Electrocatalyst approaches and challenges for automotive fuel cells”, Nature 2012. https://doi.org/10.1038/nature11115 (review)

Credit: Drawn by LabCanvas after Schmidt-Rohr & Chen, Nat. Mater. 2008 (doi:10.1038/nmat2074); Kusoglu & Weber, Chem. Rev. 2017 (doi:10.1021/acs.chemrev.6b00159); Holdcroft, Chem. Mater. 2014 (doi:10.1021/cm401445h); Kongkanand & Mathias, J. Phys. Chem. Lett. 2016 (doi:10.1021/acs.jpclett.6b00216); Jiao et al., Nature 2021 (doi:10.1038/s41586-021-03482-7); Debe, Nature 2012 (doi:10.1038/nature11115). Catalyst layer and stack schematic; channel sizes to scale.

## Questions

**What does the “PEM fuel cells: membrane, ionomer and catalyst layer, from molecule to stack” template show?** A zoom-out through a proton-exchange membrane fuel cell. The PFSA ionomer (Nafion) is a Teflon-like backbone with side chains ending in sulfonic acid; hydrated, it forms parallel water channels 1.8–3.5 nm wide through which protons move. The same ionomer coats platinum on carbon in the catalyst layer, where protons, electrons and oxygen must meet; cutting platinum to about 0.1 mg cm⁻² exposes an oxygen-transport resistance near the Pt. The cell and stack carry the power-density goals of 6 kW L⁻¹ by 2030 and 9 kW L⁻¹ by 2040.

**What are the steps shown in “PEM fuel cells: membrane, ionomer and catalyst layer, from molecule to stack”?** 1. The ionomer: A PTFE backbone with perfluoroether side chains ending in –SO₃H, which gives up its proton in water (Kusoglu & Weber 2017). 2. The membrane: Hydrated, it forms parallel water channels 1.8–3.5 nm across (mean 2.4 nm at 20 vol% water), held by crystallites of about (5 nm)² (Schmidt-Rohr & Chen 2008). 3. The catalyst layer: The ionomer is also the binder and proton path around Pt on carbon (Holdcroft 2014); at ~0.1 mg Pt cm⁻² oxygen reaching the Pt limits currents above 1 A cm⁻² (Kongkanand & Mathias 2016). 4. The stack: Power-density goals of 6 kW L⁻¹ by 2030 and 9 kW L⁻¹ by 2040 (Jiao et al. 2021).

**What are the starting materials and the product?** Starting materials: A PFSA ionomer, platinum on carbon, a gas-diffusion layer; hydrogen and air. Product: Electricity and water from a membrane electrode assembly in a stack.

**Which papers is “PEM fuel cells: membrane, ionomer and catalyst layer, from molecule to stack” based on?** Schmidt-Rohr & Chen, “Parallel cylindrical water nanochannels in Nafion fuel-cell membranes”, Nat. Mater. 2008 (doi:10.1038/nmat2074); Kusoglu & Weber, “New insights into perfluorinated sulfonic-acid ionomers”, Chem. Rev. 2017 (doi:10.1021/acs.chemrev.6b00159); Holdcroft, “Fuel cell catalyst layers: a polymer science perspective”, Chem. Mater. 2014 (doi:10.1021/cm401445h); Kongkanand & Mathias, “The priority and challenge of high-power performance of low-platinum proton-exchange membrane fuel cells”, J. Phys. Chem. Lett. 2016 (doi:10.1021/acs.jpclett.6b00216); Jiao et al., “Designing the next generation of proton-exchange membrane fuel cells”, Nature 2021 (doi:10.1038/s41586-021-03482-7); Debe, “Electrocatalyst approaches and challenges for automotive fuel cells”, Nature 2012 (doi:10.1038/nature11115).

**Can I edit the “PEM fuel cells: membrane, ionomer and catalyst layer, from molecule to stack” template?** Yes. Open it in the LabCanvas editor: all 87 layers are editable, including 3 generated objects (structures, plots, equipment) with their own settings. Change the text, colours and layout, then export PNG, TIFF or PDF at the width and DPI the journal asks for.

**Do I need an account to use this template?** Not to view it here. To open and edit it, sign in to LabCanvas or create a free account (the free plan keeps up to 3 designs). Downloading the figure is part of LabCanvas Pro (US$19 a month or US$199 a year).
