# Perovskite nanocrystals: hot injection, room-temperature reprecipitation and halide exchange

> Two routes to the same bright CsPbX₃ nanocube: hot injection of Cs-oleate into lead halide at 140–200 °C, where growth is over within 1–3 s, and ligand-assisted reprecipitation, salts in DMF dropped into toluene in air at room temperature. The halide is then swapped after synthesis, reversibly, so one batch of green CsPbBr₃ becomes blue or red, and the family covers 410–700 nm with narrow lines and quantum yields up to 90%.

- Page: https://www.labcanvas.com/templates/graphical-abstracts/perovskite-nanocrystals-hot-injection-room-temperature-reprecipitation-h
- Open in the LabCanvas editor (LabCanvas account): https://www.labcanvas.com/editor.html?template=perovskite-nanocrystals-hot-injection-larp-halide-exchange
- Updated: 2026-10-14
- Category: Graphical abstracts
- Method: Graphical abstract
- Starting materials: Cs-oleate and PbX₂ in octadecene with oleylamine and oleic acid (hot injection); PbX₂ with CsX or MAX in DMF, dropped into toluene with ligands (LARP)
- Product: Cubic CsPbX₃ nanocubes 4–15 nm across, emitting anywhere from 410 to 700 nm
- Key result: 4–15 nm cubes, 410–700 nm, fwhm 12–42 nm, QY up to 90%, 140% of NTSC (Protesescu et al. 2015); QY up to 70% by LARP (Zhang et al. 2015); 80/95/70% red/green/blue at room temperature (Li et al. 2016)
- Figure: 1920 × 1080 px, 97 editable layers (6 generated objects with settings)

## Steps

1. **Hot injection**: Cs-oleate into PbX₂ in octadecene with oleylamine and oleic acid at 140–200 °C; most growth within 1–3 s, so the temperature sets the size, 4–15 nm (Protesescu et al. 2015)
2. **Reprecipitation (LARP)**: The salts in a good solvent (DMF) dropped into a poor one (toluene) with ligands, in air at room temperature, scalable to grams (Shamsi et al. 2019); MAPbX₃ dots with QY up to 70% (Zhang et al. 2015); CsPbX₃ within seconds (Li et al. 2016)
3. **The nanocube**: Corner-sharing PbX₆ octahedra with Cs⁺ in the gaps, cubic phase, ligands on the faces; exciton Bohr diameters 5, 7 and 12 nm for Cl, Br and I (Protesescu et al. 2015)
4. **Swap the halide**: Fast, low-temperature anion exchange tunes 410–700 nm with QY 20–80% and 10–40 nm line widths (Nedelcu et al. 2015), there and back (Akkerman et al. 2015); fully reversible (Shamsi et al. 2019)

## Uses

- Graphical abstracts on halide perovskite nanocrystals
- Talks on colloidal synthesis routes and post-synthetic anion exchange
- Teaching quantum dots for displays and lighting

## References

1. Protesescu et al., “Nanocrystals of cesium lead halide perovskites (CsPbX₃, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut”, Nano Lett. 2015. https://doi.org/10.1021/nl5048779 (method origin)
2. Zhang et al., “Brightly luminescent and color-tunable colloidal CH₃NH₃PbX₃ (X = Br, I, Cl) quantum dots: potential alternatives for display technology”, ACS Nano 2015. https://doi.org/10.1021/acsnano.5b01154 (method origin)
3. Li et al., “CsPbX₃ quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes”, Adv. Funct. Mater. 2016. https://doi.org/10.1002/adfm.201600109 (primary)
4. Nedelcu et al., “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX₃, X = Cl, Br, I)”, Nano Lett. 2015. https://doi.org/10.1021/acs.nanolett.5b02404 (primary)
5. Akkerman et al., “Tuning the optical properties of cesium lead halide perovskite nanocrystals by anion exchange reactions”, J. Am. Chem. Soc. 2015. https://doi.org/10.1021/jacs.5b05602 (primary)
6. Shamsi, Urban, Imran, De Trizio & Manna, “Metal halide perovskite nanocrystals: synthesis, post-synthesis modifications, and their optical properties”, Chem. Rev. 2019. https://doi.org/10.1021/acs.chemrev.8b00644 (review)
7. Kovalenko, Protesescu & Bodnarchuk, “Properties and potential optoelectronic applications of lead halide perovskite nanocrystals”, Science 2017. https://doi.org/10.1126/science.aam7093 (further reading)

Credit: Drawn by LabCanvas after Protesescu et al., Nano Lett. 2015 (doi:10.1021/nl5048779); Zhang et al., ACS Nano 2015 (doi:10.1021/acsnano.5b01154); Li et al., Adv. Funct. Mater. 2016 (doi:10.1002/adfm.201600109); Nedelcu et al., Nano Lett. 2015 (doi:10.1021/acs.nanolett.5b02404); Akkerman et al., J. Am. Chem. Soc. 2015 (doi:10.1021/jacs.5b05602); Shamsi et al., Chem. Rev. 2019 (doi:10.1021/acs.chemrev.8b00644). Emission peaks schematic.

## Questions

**What does the “Perovskite nanocrystals: hot injection, room-temperature reprecipitation and halide exchange” template show?** Two routes to the same bright CsPbX₃ nanocube: hot injection of Cs-oleate into lead halide at 140–200 °C, where growth is over within 1–3 s, and ligand-assisted reprecipitation, salts in DMF dropped into toluene in air at room temperature. The halide is then swapped after synthesis, reversibly, so one batch of green CsPbBr₃ becomes blue or red, and the family covers 410–700 nm with narrow lines and quantum yields up to 90%.

**What are the steps shown in “Perovskite nanocrystals: hot injection, room-temperature reprecipitation and halide exchange”?** 1. Hot injection: Cs-oleate into PbX₂ in octadecene with oleylamine and oleic acid at 140–200 °C; most growth within 1–3 s, so the temperature sets the size, 4–15 nm (Protesescu et al. 2015). 2. Reprecipitation (LARP): The salts in a good solvent (DMF) dropped into a poor one (toluene) with ligands, in air at room temperature, scalable to grams (Shamsi et al. 2019); MAPbX₃ dots with QY up to 70% (Zhang et al. 2015); CsPbX₃ within seconds (Li et al. 2016). 3. The nanocube: Corner-sharing PbX₆ octahedra with Cs⁺ in the gaps, cubic phase, ligands on the faces; exciton Bohr diameters 5, 7 and 12 nm for Cl, Br and I (Protesescu et al. 2015). 4. Swap the halide: Fast, low-temperature anion exchange tunes 410–700 nm with QY 20–80% and 10–40 nm line widths (Nedelcu et al. 2015), there and back (Akkerman et al. 2015); fully reversible (Shamsi et al. 2019).

**What are the starting materials and the product?** Starting materials: Cs-oleate and PbX₂ in octadecene with oleylamine and oleic acid (hot injection); PbX₂ with CsX or MAX in DMF, dropped into toluene with ligands (LARP). Product: Cubic CsPbX₃ nanocubes 4–15 nm across, emitting anywhere from 410 to 700 nm.

**Which papers is “Perovskite nanocrystals: hot injection, room-temperature reprecipitation and halide exchange” based on?** Protesescu et al., “Nanocrystals of cesium lead halide perovskites (CsPbX₃, X = Cl, Br, and I): novel optoelectronic materials showing bright emission with wide color gamut”, Nano Lett. 2015 (doi:10.1021/nl5048779); Zhang et al., “Brightly luminescent and color-tunable colloidal CH₃NH₃PbX₃ (X = Br, I, Cl) quantum dots: potential alternatives for display technology”, ACS Nano 2015 (doi:10.1021/acsnano.5b01154); Li et al., “CsPbX₃ quantum dots for lighting and displays: room-temperature synthesis, photoluminescence superiorities, underlying origins and white light-emitting diodes”, Adv. Funct. Mater. 2016 (doi:10.1002/adfm.201600109); Nedelcu et al., “Fast anion-exchange in highly luminescent nanocrystals of cesium lead halide perovskites (CsPbX₃, X = Cl, Br, I)”, Nano Lett. 2015 (doi:10.1021/acs.nanolett.5b02404); Akkerman et al., “Tuning the optical properties of cesium lead halide perovskite nanocrystals by anion exchange reactions”, J. Am. Chem. Soc. 2015 (doi:10.1021/jacs.5b05602); Shamsi, Urban, Imran, De Trizio & Manna, “Metal halide perovskite nanocrystals: synthesis, post-synthesis modifications, and their optical properties”, Chem. Rev. 2019 (doi:10.1021/acs.chemrev.8b00644); Kovalenko, Protesescu & Bodnarchuk, “Properties and potential optoelectronic applications of lead halide perovskite nanocrystals”, Science 2017 (doi:10.1126/science.aam7093).

**Can I edit the “Perovskite nanocrystals: hot injection, room-temperature reprecipitation and halide exchange” template?** Yes. Open it in the LabCanvas editor: all 97 layers are editable, including 6 generated objects (structures, plots, equipment) with their own settings. Change the text, colours and layout, then export PNG, TIFF or PDF at the width and DPI the journal asks for.

**Do I need an account to use this template?** Not to view it here. To open and edit it, sign in to LabCanvas or create a free account (the free plan keeps up to 3 designs). Downloading the figure is part of LabCanvas Pro (US$19 a month or US$199 a year).
