# Solvothermal vs hydrothermal synthesis: one autoclave, two kinds of solvent

> The sealed, PTFE-lined autoclave set on a temperature ruler. Above it, water: hydrothermal synthesis starts above 100 °C and 1 bar, water’s dielectric constant falls from 78 to below 10, its ionic product peaks at 250–300 °C, and past the critical point (374 °C, 22.1 MPa) reactions run over 10³ times faster, making oxide particles continuously in under two minutes; LiFePO₄ forms at 300 °C. Below it, organic solvents: solvothermal synthesis above the solvent’s boiling point under autogenous pressure, usually 50–260 °C, with MOF-5 and UiO-66 made in DMF at 120–125 °C.

- Page: https://www.labcanvas.com/templates/graphical-abstracts/solvothermal-vs-hydrothermal-synthesis-autoclave-two-kinds-solvent
- Open in the LabCanvas editor (LabCanvas account): https://www.labcanvas.com/editor.html?template=solvothermal-vs-hydrothermal-autoclave-synthesis
- Updated: 2026-10-14
- Category: Graphical abstracts
- Method: Graphical abstract
- Starting materials: Salts or oxides in water (hydrothermal), or salts and organic linkers in DMF and other solvents (solvothermal), sealed in a PTFE-lined steel autoclave
- Product: Crystalline oxides, phosphates and frameworks grown at temperatures above the solvent’s boiling point
- Key result: ε(water) 78 → < 10; Kw maximum 250–300 °C; 374 °C, 22.1 MPa; rates > 10³× in supercritical water (Hayashi & Hakuta 2010); < 2 min, 20–600 nm (Adschiri et al. 1992)
- Figure: 1920 × 1080 px, 75 editable layers (3 generated objects with settings)

## Steps

1. **Seal and heat**: A closed vessel above the solvent’s boiling point builds its own (autogenous) pressure; usually polar solvents, 50–260 °C, hours to days (Raptopoulou 2021)
2. **Water changes as it heats**: Hydrothermal means aqueous media above 100 °C and 1 bar (Rabenau 1985); the dielectric constant falls from 78 to below 10, the ionic product peaks at 250–300 °C (Hayashi & Hakuta 2010)
3. **Past the critical point**: At 374 °C and 22.1 MPa water turns supercritical: reactions over 10³ times faster (Hayashi & Hakuta 2010); oxide particles of 20–600 nm continuously in under 2 min (Adschiri et al. 1992)
4. **Real recipes**: LiFePO₄ from FeSO₄, H₃PO₄ and LiOH in water at 300 °C (Ruiz-Jorge et al. 2021); MOF-5 in DMF at 125 °C for 24 h (Kumar & Masram 2021); UiO-66 in DMF at 120 °C for 24 h (Liu et al. 2023)

## Uses

- Graphical abstracts on hydrothermal and solvothermal synthesis
- Teaching how water changes near its critical point
- Talks on autoclave synthesis of oxides, battery materials and MOFs

## References

1. Rabenau, “The role of hydrothermal synthesis in preparative chemistry”, Angew. Chem. Int. Ed. Engl. 1985. https://doi.org/10.1002/anie.198510261 (review)
2. Hayashi & Hakuta, “Hydrothermal synthesis of metal oxide nanoparticles in supercritical water”, Materials 2010. https://doi.org/10.3390/ma3073794 (review)
3. Adschiri, Kanazawa & Arai, “Rapid and continuous hydrothermal crystallization of metal oxide particles in supercritical water”, J. Am. Ceram. Soc. 1992. https://doi.org/10.1111/j.1151-2916.1992.tb04179.x (method origin)
4. Ruiz-Jorge et al., “Effect of the heating rate to prevent the generation of iron oxides during the hydrothermal synthesis of LiFePO₄”, Nanomaterials 2021. https://doi.org/10.3390/nano11092412 (primary)
5. Raptopoulou, “Metal-organic frameworks: synthetic methods and potential applications”, Materials 2021. https://doi.org/10.3390/ma14020310 (review)
6. Kumar & Masram, “Sustainable synthesis of MOF-5@GO nanocomposites for efficient removal of rhodamine B from water”, ACS Omega 2021. https://doi.org/10.1021/acsomega.1c00143 (primary)
7. Liu, Lyu & Bai, “One-step synthesis of Al-doped UiO-66 nanoparticle for enhanced removal of organic dyes from wastewater”, Molecules 2023. https://doi.org/10.3390/molecules28052182 (primary)
8. Byrappa & Adschiri, “Hydrothermal technology for nanotechnology”, Prog. Cryst. Growth Charact. Mater. 2007. https://doi.org/10.1016/j.pcrysgrow.2007.04.001 (review)
9. Demazeau, “Solvothermal reactions: an original route for the synthesis of novel materials”, J. Mater. Sci. 2008. https://doi.org/10.1007/s10853-007-2024-9 (review)
10. Eddaoudi et al., “Systematic design of pore size and functionality in isoreticular MOFs and their application in methane storage”, Science 2002. https://doi.org/10.1126/science.1067208 (further reading)

Credit: Drawn by LabCanvas after Rabenau, Angew. Chem. 1985 (doi:10.1002/anie.198510261); Hayashi & Hakuta, Materials 2010 (doi:10.3390/ma3073794); Adschiri et al., J. Am. Ceram. Soc. 1992 (doi:10.1111/j.1151-2916.1992.tb04179.x); Ruiz-Jorge et al., Nanomaterials 2021 (doi:10.3390/nano11092412); Raptopoulou, Materials 2021 (doi:10.3390/ma14020310); Kumar & Masram, ACS Omega 2021 (doi:10.1021/acsomega.1c00143); Liu et al., Molecules 2023 (doi:10.3390/molecules28052182); Byrappa & Adschiri 2007; Demazeau 2008. Dielectric band a trend.

## Questions

**What does the “Solvothermal vs hydrothermal synthesis: one autoclave, two kinds of solvent” template show?** The sealed, PTFE-lined autoclave set on a temperature ruler. Above it, water: hydrothermal synthesis starts above 100 °C and 1 bar, water’s dielectric constant falls from 78 to below 10, its ionic product peaks at 250–300 °C, and past the critical point (374 °C, 22.1 MPa) reactions run over 10³ times faster, making oxide particles continuously in under two minutes; LiFePO₄ forms at 300 °C. Below it, organic solvents: solvothermal synthesis above the solvent’s boiling point under autogenous pressure, usually 50–260 °C, with MOF-5 and UiO-66 made in DMF at 120–125 °C.

**What are the steps shown in “Solvothermal vs hydrothermal synthesis: one autoclave, two kinds of solvent”?** 1. Seal and heat: A closed vessel above the solvent’s boiling point builds its own (autogenous) pressure; usually polar solvents, 50–260 °C, hours to days (Raptopoulou 2021). 2. Water changes as it heats: Hydrothermal means aqueous media above 100 °C and 1 bar (Rabenau 1985); the dielectric constant falls from 78 to below 10, the ionic product peaks at 250–300 °C (Hayashi & Hakuta 2010). 3. Past the critical point: At 374 °C and 22.1 MPa water turns supercritical: reactions over 10³ times faster (Hayashi & Hakuta 2010); oxide particles of 20–600 nm continuously in under 2 min (Adschiri et al. 1992). 4. Real recipes: LiFePO₄ from FeSO₄, H₃PO₄ and LiOH in water at 300 °C (Ruiz-Jorge et al. 2021); MOF-5 in DMF at 125 °C for 24 h (Kumar & Masram 2021); UiO-66 in DMF at 120 °C for 24 h (Liu et al. 2023).

**What are the starting materials and the product?** Starting materials: Salts or oxides in water (hydrothermal), or salts and organic linkers in DMF and other solvents (solvothermal), sealed in a PTFE-lined steel autoclave. Product: Crystalline oxides, phosphates and frameworks grown at temperatures above the solvent’s boiling point.

**Which papers is “Solvothermal vs hydrothermal synthesis: one autoclave, two kinds of solvent” based on?** Rabenau, “The role of hydrothermal synthesis in preparative chemistry”, Angew. Chem. Int. Ed. Engl. 1985 (doi:10.1002/anie.198510261); Hayashi & Hakuta, “Hydrothermal synthesis of metal oxide nanoparticles in supercritical water”, Materials 2010 (doi:10.3390/ma3073794); Adschiri, Kanazawa & Arai, “Rapid and continuous hydrothermal crystallization of metal oxide particles in supercritical water”, J. Am. Ceram. Soc. 1992 (doi:10.1111/j.1151-2916.1992.tb04179.x); Ruiz-Jorge et al., “Effect of the heating rate to prevent the generation of iron oxides during the hydrothermal synthesis of LiFePO₄”, Nanomaterials 2021 (doi:10.3390/nano11092412); Raptopoulou, “Metal-organic frameworks: synthetic methods and potential applications”, Materials 2021 (doi:10.3390/ma14020310); Kumar & Masram, “Sustainable synthesis of MOF-5@GO nanocomposites for efficient removal of rhodamine B from water”, ACS Omega 2021 (doi:10.1021/acsomega.1c00143); Liu, Lyu & Bai, “One-step synthesis of Al-doped UiO-66 nanoparticle for enhanced removal of organic dyes from wastewater”, Molecules 2023 (doi:10.3390/molecules28052182); Byrappa & Adschiri, “Hydrothermal technology for nanotechnology”, Prog. Cryst. Growth Charact. Mater. 2007 (doi:10.1016/j.pcrysgrow.2007.04.001); Demazeau, “Solvothermal reactions: an original route for the synthesis of novel materials”, J. Mater. Sci. 2008 (doi:10.1007/s10853-007-2024-9); Eddaoudi et al., “Systematic design of pore size and functionality in isoreticular MOFs and their application in methane storage”, Science 2002 (doi:10.1126/science.1067208).

**Can I edit the “Solvothermal vs hydrothermal synthesis: one autoclave, two kinds of solvent” template?** Yes. Open it in the LabCanvas editor: all 75 layers are editable, including 3 generated objects (structures, plots, equipment) with their own settings. Change the text, colours and layout, then export PNG, TIFF or PDF at the width and DPI the journal asks for.

**Do I need an account to use this template?** Not to view it here. To open and edit it, sign in to LabCanvas or create a free account (the free plan keeps up to 3 designs). Downloading the figure is part of LabCanvas Pro (US$19 a month or US$199 a year).
